TE Connectivity Micro-MaTch Series Flat Ribbon Cable, 14-Way, 1.27mm Pitch, 75.5mm Length, Micro-MaTch IDC to
Tehnička dokumentacija
Tehnički podaci
Capacitance Range
0.2 pF → 33pF
Terminated/Unterminated
Terminated
EN166 Eye Protection
3, 4, 5, B, T
Package Type
PG-TDSON-8-7
Screened/Unscreened
Unscreened
Number of Ways
14
Pitch
1.27mm
American Wire Gauge
28 AWG
Nominal Dimensions
12 x 20 x 15in
Manufacturer Series
SIMATIC OPC UA S7-1200
Sheath Colour
Grey
Operating Temperature Range
-40 → +105 °C
Model
CS-64
Series
Micro-Match
Brand
TE ConnectivityZemlja podrijetla
Netherlands
Detalji o proizvodu
Evaluation Board for ADL5201 Variable Gain Amplifier (VGA)
Analog Devices’ ADL5201-EVALZ is an evaluation board for the ADL5201 device. The ADL5201 is a digitally controlled, variable gain, wide band-width amplifier that provides precise gain control, high IP3, and low noise figure. The excellent distortion performance and high signal bandwidth make the ADL5201 an excellent gain control device for a variety of receiver applications.
For standard operation, this fully populated, 4-layer, FR4-based evaluation board requires a 5 V power supply capable of delivering 500 mA and a 3.3 V power supply capable of delivering 1 mA. The 5 V supply is connected to the test loops labeled VPOS and GND and is the bias for the main amplifier. The open collector outputs are connected to the main bias via the power plane. The 3.3 V supply is connected to the test loops labeled 3.3 V and GND. The RF input is applied to the SMA connector labeled INB-. The RF output is available at the SMA connector labeled OUTB-. A fully differential input and output is easily configured by removing R3 and R47, installing a zero ohm jumper at R4 and R48, removing T1 and T2 and placing jumpers across the transformer pads. The gain control options are controlled via the on board USB micro controller.
The ADL5201-EVALZ evaluation board can be programmed through the USB port of a PC running Windows XP or Vista with Microsoft .NET Framework 3.5 installed. Manual operation of the gain control functions is possible using the 3 pin headers and supplied jumpers. Power up is controlled using the 3 pin header labeled PWUP or an external control signal maybe applied using the SMA connector labeled PWUP.
Variable Gain Amplifiers (VGA)
Variable-Gain or Voltage-Controlled Amplifiers are electronic differential amplifiers that vary their gain depending on a control voltage. Applications include audio level compression, synthesizers and amplitude modulation.
Informacije o stanju skladišta trenutno nisu dostupne.
Provjerite ponovno kasnije.
KM 10,057
Each (In a Box of 100) (bez PDV-a)
KM 11,767
Each (In a Box of 100) (s PDV-om)
100
KM 10,057
Each (In a Box of 100) (bez PDV-a)
KM 11,767
Each (In a Box of 100) (s PDV-om)
100
Tehnička dokumentacija
Tehnički podaci
Capacitance Range
0.2 pF → 33pF
Terminated/Unterminated
Terminated
EN166 Eye Protection
3, 4, 5, B, T
Package Type
PG-TDSON-8-7
Screened/Unscreened
Unscreened
Number of Ways
14
Pitch
1.27mm
American Wire Gauge
28 AWG
Nominal Dimensions
12 x 20 x 15in
Manufacturer Series
SIMATIC OPC UA S7-1200
Sheath Colour
Grey
Operating Temperature Range
-40 → +105 °C
Model
CS-64
Series
Micro-Match
Brand
TE ConnectivityZemlja podrijetla
Netherlands
Detalji o proizvodu
Evaluation Board for ADL5201 Variable Gain Amplifier (VGA)
Analog Devices’ ADL5201-EVALZ is an evaluation board for the ADL5201 device. The ADL5201 is a digitally controlled, variable gain, wide band-width amplifier that provides precise gain control, high IP3, and low noise figure. The excellent distortion performance and high signal bandwidth make the ADL5201 an excellent gain control device for a variety of receiver applications.
For standard operation, this fully populated, 4-layer, FR4-based evaluation board requires a 5 V power supply capable of delivering 500 mA and a 3.3 V power supply capable of delivering 1 mA. The 5 V supply is connected to the test loops labeled VPOS and GND and is the bias for the main amplifier. The open collector outputs are connected to the main bias via the power plane. The 3.3 V supply is connected to the test loops labeled 3.3 V and GND. The RF input is applied to the SMA connector labeled INB-. The RF output is available at the SMA connector labeled OUTB-. A fully differential input and output is easily configured by removing R3 and R47, installing a zero ohm jumper at R4 and R48, removing T1 and T2 and placing jumpers across the transformer pads. The gain control options are controlled via the on board USB micro controller.
The ADL5201-EVALZ evaluation board can be programmed through the USB port of a PC running Windows XP or Vista with Microsoft .NET Framework 3.5 installed. Manual operation of the gain control functions is possible using the 3 pin headers and supplied jumpers. Power up is controlled using the 3 pin header labeled PWUP or an external control signal maybe applied using the SMA connector labeled PWUP.
Variable Gain Amplifiers (VGA)
Variable-Gain or Voltage-Controlled Amplifiers are electronic differential amplifiers that vary their gain depending on a control voltage. Applications include audio level compression, synthesizers and amplitude modulation.